• sexto: five relay channels, independently configurable with six buttons

• quinto: five relay channels, independently configurable

• quarto: four relay channels, independently configurable

• trio: three relay channels, independently configurable

• duo: two relay channels, independently configurable

• solo: one relay channel, independently configurable

​Whether one switch or five, the HELTUN Touch Panel Switch is still "Impossibly Thin" and

"Impossibly Smart". 

The main power input can be either 85-265VAC or 12-48VDC.

​There are five relay outputs each with a maximum 5 Amp load.

There are also two independent inputs for relay channels which allow control of systems with different power sources, or to use outputs as dry contacts: e.g. to switch On/Off 220VAC lights and control motorized valves with 24VDC power.

​Input 1 with the required power source is for relay channels 1, 2 and 3, which can carry a maximum 15 Amp load.

​Input 2 with the required power source is for relay channels 4 and 5, which can carry a maximum 10 Amp load.

​Each relay channel uses HELTUN Advanced Zero-Cross Technology to deliver greatly increased longevity & reliability of your system.

The HELTUN built-in Power Consumption System precisely monitors how much energy you used during any particular day, week, or month. Do your current light switches do that?

​

Just specify the consumption of the load in watts for each relay channel and the Relay Switch quinto logic will calculate total consumption relative to the time since the output was in the ‘ON’ state.

We have also designed the circuitry so it draws almost zero watts to power itself when in standby mode. This saves you energy and money especially if your home is equipped with many HELTUN products.

1) Each of the five buttons can control any relay output. Also, the output of 1-5 relays can be controlled by each button.

2) There are five modes that can be configured for each button:

• Invert State - when button is touched: turn ON if OFF, or turn OFF if ON.

• Momentary - switch ON when button is touched, switch OFF when released.

• Momentary Reversed - switch OFF when touched, switch ON when released.

• Switch ON Only - when touched.

• Switch OFF Only - when touched.

3) Relay outputs can be controlled by a timer. For example, pressing a button can switch a relay ON, and after a specified time it can automatically be switched OFF (or vice-versa: OFF, then ON). This function can be used to open or close garage doors, gates, blinds, curtains, locks, etc., and then return them to their previous state with no additional input.

4) Each touch-sensitive ‘button’, its backlight, and associated relay output, can be independently managed by a Z-Wave controller or associated device - and can run scenes with the backlight indicating scene state or device status.

The HELTUN Touch Panel Switch does a lot more than just control house lights. You can use it to control motorized blinds, curtains, garage doors, driveway gates, and electric locks. You have full control over programming different buttons for specific functions.

For example, you can designate the top left button to raise the living room blinds, and the bottom left button to lower them. In this mode, if the blinds are rising and you then touch the down button, the system will automatically cancel the UP command and initiate a DOWN command, or vice-versa.

The system also calculates the position of the blinds when fully opened or closed and automatically stops the motor when it reaches the UP or DOWN limit. 

​If you have installed a door sensor - as on a garage door - you can associate that sensor with the button backlight to indicate the actual UP or DOWN state of the door.

Using the internal timekeeping of the HELTUN Touch Panel Switch, you can create schedules for some devices.

For example:

• Open the blinds at 7:00AM and close them at 10:00PM

• Switch on the porch light at 7:00PM and turn it off at 1:00AM.

Scenarios can also be created that allow connected devices to be triggered by a sensor.

For example:

• If the ambient light sensor detects less then 200 lux, connected house lights would switch to ON.

• If the internal temperature sensor measured less than 23°C, the connected heating system could be switched on.

​

The possibilities for adding convenience and comfort are endless and limited only by the creativity of the owner or installer of the HELTUN Touch Panel Switch.